You can also take the floor mat off. Use a screwdriver to turn the bolts holding the governor clockwise to increase the speed.
The spring accelerated governor is right below this panel.
How to adjust a governor on a yamaha golf cart. This is the way to increase the top speed on your Yamaha G29 Drive Gas Golf with a simple governor adjustment. The first option to making your cart faster is to replace the electronic speed control. Use a 10mm wrench and tighten the nut a little by moving it in to expose the threaded rod a little more.
This can be done by doing a 14 turn of the screw. The valves can be adjusted using a flat screwdriver a feeler gauge and a 10mm wrench. Adjust the main cable nut holding it in place with the screwdriver.
Reply to Jiveys Post. Barry at DIY Golf Cart shows you how to properly adjust the governor on a Yamaha G29 Drive gas golf cart. Whether its located at the carburetor or sticking out as a pivot point from the differential the principle is the same.
Removing and Adjusting The Yamaha Golf Cart Governor. Unfortunately this upgrade is not. The only tools you will need is a 10mm wrench.
We have a golf cart with added seats on back for grand children. This is not an answerthe only speed limiter on a yamaha gas golf cart is the governer. While you may end up having an engine that is in the front rather than the back rare but is possible on some Yamaha carts or may have to use different sized screwdrivers including various standard models.
You can find the governor by tracing the thickest cable running from the gas pedal. This is a basic and easy governor modification for the Yamaha. The bad news is there is no governor on an electric golf cart but the good news is there are several options to quench your need for speed.
This will enable more voltage to pass to the motor producing the desired result. I am running all the gearing the engine can handle due to the larger diameter wheels and tiresI still dont know how to adjust the governer to increase engine speed to 48-5000 RPMJivey I saw your querry at buggies unlimited I am a regular there but thanks for trying. How to adjust the governor to get more top end speed and make your Yamaha G29 gas Golf Cart go faster.
Youll see some type of spring loaded mechanism in line with the golf carts accelerator system. Locate the golf carts governor. In this video it lays out the steps on making your cart go faster without doing any damage to the golf car.
Adjusting the tension on the spring will either increase. Tighten the locknut keeping the plastic. How to Adjust the Governor on a Gas E-Z-Go Golf Cart Locate the governor arm mounted on top of the rear axle case underneath the cart.
Remove the screws on both the side panels of the golf cart using the T-45 bit. Turning the nut counter-clockwise will make the cable longer allowing the cart to go faster. Retighten the adjusting locknut.
Run the cable on the gas pedal to the carburetor and reattach it at the original position of the governor cable. We were told to adjust. There are some simple steps involved in removing the secondary clutch on a Yamaha golf cart.
Remove the screws connected to the. Remove the rear inspection panel from the golf cart. First of all identify the right clutch puller according to the VIN number of the golf cart you are operating.
Locate the cable nut that holds the cable to the throttle lever for a clutch cable governor. Just carefully follow the given steps. How to remove a secondary clutch on a Yamaha golf cart.
This cable runs through the governor on its way to the carburetor. This is a Yamaha G29 year is 2009 and is gas powered. Adjusting the governor on a Yamaha golf cart begins with detaching a spring adjustment cable from the carburetor.
The first common golf cart governor type is mechanical and is common on many makes and models. Rod assembly 2 adjustment Adjust the rod assy 2 length by turning the shaft so that when the throttle valve is at a closed idle position by pushing the speed limiter lever slightly the exhaust valve is a t a closed position as illustrated on the next page. Golf cart doesnt seem to go as fast as our last cart.
Do a valve clearance adjustment starting with the cold valve. Most golf carts are limited in their speed from t. What is interesting about the Yamaha governor removal process is that it is basically the same as that with the EZGO cart.
How to adjust the governor on 2014 Yamaha G29 Golf cart. Adjust the idle jet pilot screw on the carburetor. Loosen the adjusting locknut on the end of the governor spring.
The following steps will help you to adjust the throttle on an EZGO RXV golf cart using a drill a 10mm wrench and a T-45 bit. The following steps show you how to adjust the governor on your Yamaha G29 golf cart. This video show you a quick and easy way to increase the maximum speed limit without having to buy anything.